Cutout Template
188 mm x 275 mm
(7.4” x 10.8”)
Paint Guard
SI 26W
In-Wall Speaker
User’s Guide
1
4
Determine the speaker location.
Insert the speaker into the wall opening.
Leave at least 1” clearance from the edge of the speaker
to the studs in all directions. Hold or tape template in location,
make sure template is level. Trace along the inside of the template.
Loosen the six screws on the front baffle (counter-
clockwise) 1/2 turn. Then tighten the screws (clockwise)
until the dog legs clamp the speaker to the wall.
At least 1” from the stud.
Trace template
2
5
Carefully cut a hole along the inside of the traced line.
Level speaker, position each wall clamp outward, and tighten
each screw until snug.
Install dust shield to protect the speaker during ongoing
construction.
Cut material
CAUTION
Do not over-tighten screws.
3
Attach the speaker wires to the 2-pole captive screw plug.
Use red for the positive (+) wire and black for the negative (-)
wire. Insert the 2-pole captive screw plug into the 2-pole
connector on back of the speaker.
Dust Shield
6
Remove the dust shield,
install the speaker grill.
eaker
SI 26W
Sp
e
a
l
l
a
s
n
c
In-W
m
Impedh
O
8
0
X 00/0
X
X
X
X
E
X
X
X
X
X
X
X
X
N
S
SA
U
eered in
Engin
Specifications:
Application diagram:
Acoustic & Electrical
Speaker type.................................. 2-way in-wall speaker
Frequency range........................... 40 Hz to 20 kHz, -10 dB, half space
Power capacity.............................. 60 W continuous program,
30 W continuous pink noise
T
PU
T
OU
T
F
I
ED
E
L
IF
PL
T
M
A
IGH
R
12V
IR
Rx
B
Tx
C
/M
C/IR
L
A
2
3
2
P
RS-
AM
PRE
Nominal sensitivity......................
Nominal impedance .................... 8 ohms
Crossover frequency................... 2.5 kHz
Woofer........................................... 6.5" (165 mm) polypropylene cone with
moisture resistant coating
89 dB, 1 W, 1 m, half space
S
T
PU
2
T
NEOU
IN
IO
D
1
I
L
U
L
A
SI 26W
Two-way In-wall
Speaker
Projector
L
IX
M
X/
ST
U
U
J
A
D
B
A
R
-42d
O
T
B
24d
R
+
IO
IO
D
U
A
S
EL
R
T
EV
PU
L
O
IN
E
M
O
IN
N
L
D
U
A
5
6
R
B
S
G
T
PU
T
OU
O
IT
N
O
M
R
S
T
E
D
PU
IN
VI
Extron
MLS 304SA
MediaLink Switcher
z
50-60H
2
V
100-240
1
Tweeter.......................................... 0.75" (19 mm) titanium dome
X.
A
M
1.0A
General
Temperature/humidity...............
Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Laptop
w/ Audio
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Warranty ....................................... 5 years parts and labor
PC
VCR
68-1101-01 Rev A
08 07
NOTE: All nominal levels are at 10%.
NOTE: Specifications are subject to change without notice.
Print at 100%. - Do Not “Fit to Paper”.
|