g
IRONS
FER À REPASSER PLANCHA
/
Model Numbers / Numéros de modèles / Números de Modelos:
106671R, 169153, 106822R, 106820, 169133, 169134, 169159, 169194
UPC: 681131066716, 681131691536, 681131068208, 681131691338, 681131691345,
681131691598, 681131691949
Customer Assistance / Service à la clientèle / Asistencia al Cliente
1 877 207 0923 (US) • 1 877 556 0973 (Canada)
Thank you for purchasing a GE small appliance.
In keeping with the GE ecomagination initiative, please consider the option to recycle the packaging
material and donate the properly functioning appliance and corresponding Use & Care Guide you
are no longer using.
To read more about GE’s ecomagination commitment visit:
ge.ecomagination.com
Merci d'avoir acheté ce petit appareil GE.
Afin de poursuivre l'initiative écomagination de GE, veuillez recycler les matériaux d'emballage et faire don d'un
appareil fonctionnant adéquatement que vous n'utilisez plus ainsi que le guide d'utilisation et d'entretien.
Pour en savoir plus à propos de l'engagement écomagination de GE, visitez le site :
ge.ecomagination.com
Gracias por comprar un pequeño electrodoméstico de GE.
Siguiendo la iniciativa ecoimaginación de GE, por favor considere la opción de reciclar el material de empacado
y donar el aparato funcionando adecuadamente y la Guía de Cuidado y Uso correspondiente que ya no use.
Para leer más sobre el compromiso de ecoimaginación de GE visite:
ge.ecomagination.com
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed including
the following:
READ ALL INSTRUCTIONS BEFORE USING
•
•
•
Use iron only for its intended use.
To protect against risk of electric shock, do not immerse the iron in water or other liquids.
The iron should always be turned to OFF ( O ) before plugging or unplugging from outlet.
Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Fully
retract cord within unit or loop cord loosely around iron, as applicable, when storing.
Always disconnect iron from electrical outlet when filling with water or emptying and when
not in use.
•
•
•
Do not operate iron with a damaged cord or if the iron has been dropped or damaged.
To avoid the risk of electric shock, do not disassemble the iron. Call our toll-free customer
assistance number for information on examination and repair. Incorrect reassembly can
cause a risk of electric shock when the iron is used.
•
•
Close supervision is necessary for any appliance being used by or near children. Do not leave
iron unattended while connected or on an ironing board.
Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you
turn a steam iron upside down – there may be hot water in the reservoir.
SPECIAL INSTRUCTIONS
To avoid a circuit overload, do not operate another high wattage appliance on the same
circuit.
If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords
rated for less amperage may overheat. Care should be taken to arrange the cord so
that it cannot be pulled or tripped over.
•
•
SAVE THESE INSTRUCTIONS!
OTHER CONSUMER SAFETY INFORMATION
This appliance is for HOUSEHOLD USE ONLY.
WARNING! Shock Hazard: This appliance has a polarized plug (one wide blade) that reduces the
risk of electric shock. The plug fits only one way into a polarized outlet. Do not defeat the safety
purpose of the plug by modifying the plug in any way or using an adaptor. If the plug does not
fit, reverse the plug. If it still does not fit, have an electrician replace the outlet.
Use the iron on an ironing board. Ironing on any other surface may damage that surface.
Do not iron or vertical steam clothes that are being worn.
Do not use vertical steam in the direction of people or pets.
2
PARTS
1
2
3
4
10
5
9
6
8
7
11
13
14
15
12
1. Cord
2. Blast of Steam/Spray
Buttons (see inset)
9. Power ON/Auto Shutoff
Reset Button/Light
10. Heel Rest
3. Adjustable Steam
Switch (see inset)
4. Water Tank Opening
5. Spray Nozzle
11. Adjustable Steam Switch
12. Blast of Steam Button
13. Spray Button
14. Retractable Cord
(on select models)
6. Water Window
7. Temperature Control
Dial
15. Cord Release Button
(on select models)
8. Soleplate
3
OPERATION
Before first use
• Steam vents (located on bottom of soleplate) should be cleaned before first use.
• During the first use of the iron, it may appear to smoke. This will stop and does not
indicate a defect or hazard.
• To clean steam vents before first use, prepare iron for steam ironing. See “To steam
iron” section. Then iron over an old cloth for a few minutes while letting the iron
steam. Press the Blast of Steam button several times to clean the vents. Then follow
the instructions in “Cleaning—How to clean.”
• Many irons spit or sputter during the first few uses with tap water. This happens as the
steam chamber becomes conditioned. This will stop after a few uses.
To dry iron
• Plug iron into outlet.
• Turn Adjustable Steam Switch to Dry Iron O.
• Turn Temperature Control Dial to desired temperature. Allow two minutes for iron to
reach desired temperature.
• To turn iron OFF (O), turn Temperature Control Dial to OFF (O) and unplug iron.
To steam iron
• Unplug iron. Turn Adjustable Steam Switch to Dry Iron O. Set iron upright on
heel rest.
• Using a cup, slowly pour tap water into water tank opening until MAX fill line has
been reached. Do not fill iron directly from the faucet.
• Plug iron into outlet.
• Turn the Temperature Control Dial to desired fabric setting in the steam range.
• Allow two minutes for the iron to reach desired temperature.
• Set Adjustable Steam Switch to the recommended steam level. See the “Fabric
Setting Chart.”
• To turn iron off, set Adjustable Steam Switch to Dry Iron O. Turn the Temperature
Control Dial to OFF ( O ). Unplug iron.
• Empty water from the iron following directions in “Cleaning—How to clean.”
Water
Please use ordinary tap water. If you have extremely hard water, alternate between
tap water and distilled water for use in the iron.
4
FABRIC SETTING CHART
Steam
Setting
Ironing Instructions
Temperature Setting
Off
Dry iron using spray if necessary.
Dry iron on the wrong side of the fabric.
Iron while fabric is still damp.
Nylon, Acrylic
Silk
•
•
O
Polyester
Wool
••
••
Use a press cloth and steam iron on the
wrong side of fabric.
Rayon
Iron using spray if necessary.
•••
•••
Cotton,
Linen
For cotton, iron while still damp or use spray.
For linen, iron fabric on wrong side.
CLEANING
Iron
• The water tank of your iron should be emptied after each use. Turn Temperature
Control Dial to OFF ( O ). Unplug the iron and hold over a sink. Slowly tilt pointed end
of iron down over sink. Water will run out of water tank opening.
• After iron has completely cooled, fully retract cord into iron or loop cord loosely
around iron, as applicable, and store in an upright position. NOTICE: Do not store
iron laying flat on soleplate.
Soleplate
• Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the
soleplate.
• To clean occasional buildup on the soleplate, wipe with a sudsy cloth. Do not use
abrasive cleansers or metal scouring pads.
• Always store iron upright in the heel rest position.
How to clean
To keep the steam vents clear of any buildup and to avoid damaging the soleplate, fol-
low these instructions each time you iron using steam.
• Turn Temperature Control Dial to OFF ( O ) and set Adjustable Steam Switch to Dry
Iron O. Fill iron with water to 1⁄2 of its maximum capacity.
• Turn Temperature Control Dial to Linen setting and let iron heat for 2 minutes. Keep
Adjustable Steam Switch on Dry Iron O.
• Turn Temperature Control Dial to OFF ( O ). Unplug iron and hold over a sink with
soleplate facing down.
• Turn Adjustable Steam Switch to MAX, while pressing Blast of Steam button often.
Boiling water and steam will flow out of steam vents. Allow all water to drain from iron.
• Gently tilt iron up and down to allow water to clean entire soleplate area.
• If water still remains inside of soleplate, reheat iron as indicated in Step 2. Boiling
water and steam could still flow out of steam vents.
5
FEATURES (on select models)
Adjustable Steam Switch
This knob provides steam for fabrics such as wool and linen. See the “Fabric Setting
Chart” for details. Set the switch to Dry Iron O to iron without steam.
Spray and Blast of Steam Buttons
Push Blast of Steam Button for an extra blast of steam. Push Spray Button to release a
fine spray of water for difficult wrinkles in cotton or linen.
Power ON/Auto Shutoff Reset Button/Light
This light comes on when the iron is first plugged in. After one hour, the iron will shut
off and the light will go out. Push the Reset Button/Light to turn
the iron back on.
Power ON Light
On units not provided with Auto Shutoff, this light comes on when the iron is plugged
in and remains on until the iron is unplugged. The light stays on even if Temperature
Control Dial is turned to OFF ( O ).
Retractable Cord
• Pull cord to desired length. Do not unwind cord beyond colored tape indicator
on cord.
• To store cord, press and hold the Cord Release Button while guiding the cord into
the storage area.
w WARNING To reduce the risk of an eye injury, hold the
plug while retracting the cord.
6
TROUBLESHOOTING
PROBLEM
THINGS TO CHECK
Iron won’t heat.
• Is the iron plugged in and the outlet working?
Check the outlet by plugging in a lamp.
• Is the Temperature Control Dial turned to a fabric setting?
• If auto shutoff model, is the Reset Button/Light illuminated?
If not, push to reset.
Water is leaking
out of the iron.
• Do not overfill the water tank.
• If steam ironing, is Adjustable Steam Switch in a steam
position and the Temperature Control Dial in the steam
range? Did the iron have enough time to preheat?
• If dry ironing, make sure the Adjustable Steam Switch is in
the DRY IRON/O position.
Iron won’t steam.
• Check the water level. If water level is low, fill using a cup
with tap water to MAX fill line.
• Is the Adjustable Steam Switch in a steam position?
• Has the iron had enough time to preheat?
Iron leaves spots
on clothing.
• ALWAYS empty the water tank of the iron after using.
Water left in the tank may discolor clothing and soleplate.
Wrinkles not
removed.
• Check Temperature Control Dial is set to correct fabric.
• Check Temperature Control Dial and set to lower setting.
Allow iron to cool down 5 minutes before continuing.
Fabric/clothing
scorched.
• If the cord should become twisted, first clear the steam
vents and empty water from water tank. See “How to
clean” section. Then turn iron to OFF (O), turn Temperature
Control Dial to OFF (O), and unplug iron. Let cool. Make sure
all water has been emptied from iron; then hold iron cord in
the middle of entire length. Let plug and iron dangle freely
until cord uncoils. This will extend the life of your iron cord.
Twisted cord.
Retractable cord
will not unwind (on
select models).
• Rewind a small amount of cord then fully depress the Cord
Release Button and pull the cord to desired length.
7
CUSTOMER ASSISTANCE
If you have a claim under this warranty, please call our Customer Assistance Number.
For faster service, please have the model number and product name ready for the
operator to assist you. This number can be found on the bottom of your appliance and
on the front page of this manual.
Model: __________________ Type: __________________ Series: ________________
Customer Assistance Number 1.877.207.0923 (US) or 1.877.556.0973 (Canada)
Keep these numbers for future reference!
How does state law relate to this warranty?
• This warranty gives you specific legal rights,
and you may also have other rights which
vary from state to state or province to
province.
Two-Year Limited Warranty
What does your warranty cover?
• Any defect in material or workmanship.
For how long after the original purchase?
• Two years.
• THIS WARRANTY IS IN LIEU OF ANY OTHER
WARRANTY OR CONDITION, WHETHER
EXPRESS OR IMPLIED, WRITTEN OR ORAL,
INCLUDING, WITHOUT LIMITATION, ANY
STATUTORY WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, EXCEPT TO THE
EXTENT PROHIBITED BY LAW.
• WAL-MART, GE, AND THE PRODUCT
MANUFACTURER EXPRESSLY DISCLAIM ALL
RESPONSIBILITY FOR SPECIAL, INCIDENTAL,
AND CONSEQUENTIAL DAMAGES OR LOSSES
CAUSED BY USE OF THIS APPLIANCE. ANY
LIABILITY IS EXPRESSLY LIMITED TO AN
AMOUNT EQUAL TO THE PURCHASE PRICE
PAID WHETHER A CLAIM, HOWEVER
INSTITUTED, IS BASED ON CONTRACT,
INDEMNITY, WARRANTY, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY, OR OTHER-
WISE. SOME STATES OR PROVINCES DO NOT
ALLOW THIS EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL LOSSES SO
THE FOREGOING DISCLAIMER MAY NOT
APPLY TO YOU.
What will we do?
• Provide you with a new one.
• For those items still under warranty but no
longer available, WAL-MART reserves the
right to replace with a similar GE branded
product of equal or greater value.
How do you make a warranty claim?
• Save your receipt.
• Properly pack your unit. We recommend
using the original carton and packing
materials.
• Return the product to your nearest
WAL-MART store or call Customer
Assistance at 1-877-207-0923 (U.S.)
or 1-877-556-0973 (Canada).
What does your warranty not cover?
• Parts subject to wear, including, without
limitation, glass parts, glass containers,
cutter/strainer, blades, seals, gaskets, clutches,
motor brushes, and/or agitators.
• Commercial use or any other use not found
in printed directions.
• Damage from misuse, abuse, or neglect,
including failure to clean product regularly
in accordance with manufacturer’s
instructions.
What if you encounter a problem with
this product while using it outside the
country of purchase?
• The warranty is valid only in the country of
purchase and you follow the warranty
claim procedure as noted.
is a trademark of General Electric
Company and is used under the
license by WAL-MART Stores, Inc.,
Marketed in Canada by:
Wal-Mart Canada Corp.
1940 Argentia Road, Mississauga,
Ontario L5N1P9
Bentonville, AR 72716
g
|