QuickStart
V420/Mini Plus
Shown Mini Plus; V420 operates in the same manner.
Features of Your FoodSaver Appliance
A
B
C
D
Indicator Light
Open/Cancel Button
Accessory Port
Accessory Hose
Note: This appliance is a compact design that saves counter space.
It can be used with pint-size and quart-size FoodSaver Bags, and 6-inch
and 8-inch FoodSaver Rolls, plus any FoodSaver accessory.
E
F
Vacuum Channel
Rubber Gasket
Sealing Strip
G
For important safety information and helpful tips, please refer to the FoodSaver Reference Guide
1-877-804-5383 (Canada). Get tips on vacuum packaging and order FoodSaver accessories.
FoodSaver Accessories
Accessories include FoodSaver Vacuum Packaging Canisters, Universal Lids, Jar Sealers and Bottle Stoppers.
FoodSaver Accessory Guidelines
1. Always leave at least one inch of space between
contents and rim.
2. Wipe rim of canister, container or bottle to ensure
it is clean and dry.
3. Place lid on canister or container, or place stopper
in bottle.
4. For accessories with a large knob on lid, turn knob
toVacuum. Vacuum package using instructions
below. When vacuum process is complete, turn
knob to Closed before removing Accessory Hose.
5. For accessories without a large knob on lid,
vacuum package using instructions below.
How toVacuum Package with FoodSaver Accessories
Insert Accessory Hose
Press and Release Lid
1. Prepare container according to FoodSaver
Accessory Guidelines above.
4. When motor and light turn off, release lid. Vacuum
process is complete.
2. Insert one end of Accessory Hose (D) into
Accessory Port (C) on appliance. Insert other
end into port on accessory. Twist gray tab while
inserting to ensure a tight fit.
5. Gently twist and remove Accessory Hose from
accessory and appliance.
6. To test vacuum, simply tug on accessory lid.
It should not move.
3. To begin vacuum process, press down firmly on
lid with both hands and hold. Motor and Indicator
Light (A) will turn on as vacuum process begins.
Note: For important tips on using accessories
with different foods, please refer to the FoodSaver
Reference Guide.
How to Open FoodSaver Accessories afterVacuum Packaging
FoodSaverVacuum Packaging Canisters
(without large knob on lid)
FoodSaver Jar Sealer with Mason Jars
®
®
For use with Ball and Kerr brand Mason jars.
To release vacuum and open, push gray rubber
button on lid.
IMPORTANT: Do NOT use screw bands when
vacuum packaging jars. To open, wedge spoon
between Mason jar lid and highest part of threaded
rim. Twist spoon gently to release vacuum.
FoodSaver Bulk Canisters and Quick Marinators
(with large knob on lid) and Universal Lids
To release vacuum and open, turn knob on lid
to Open.
FoodSaver Bottle Stoppers
To release vacuum and open, twist and pull up on
Bottle Stopper.
Tips for Successful Vacuum Packaging
For more usage tips and safety information, please refer to the FoodSaver Reference Guide or visit our website at www.foodsaver.com.
GeneralTips
If appliance lid is locked, press Open/Cancel
Button (B) to open lid.
Sealing a Bag
Make sure you’ve placed the bag in the proper place.
When making a bag from a roll, make sure end of cut
piece is on Sealing Strip (G), not over rubber gasket
(F) or in Vacuum Channel (E).
excess liquids. Just be sure to leave at least 3 inches
between paper towel and end of bag so that bag
seals properly with paper towel inside.
Make sure you give appliance time to cool down.
Wait at least 20 seconds between seals. Under very
heavy usage, appliance will shut off automatically to
prevent overheating. If it does, wait 20 minutes to
allow appliance to cool off.
Prevent moisture or liquid from being pulled into
theVacuum Channel or trapped in the seal. Either
pre-freeze moist foods such as raw meat for 1-2
hours before vacuum packaging, or place a folded
paper towel between food and end of bag to absorb
Removing Air from a Bag
Make sure you’ve placed the bag in the proper
place. When vacuuming packaging, make sure open
end of bag is inside Vacuum Channel (E).
If motor runs for more than 30 seconds without
stopping, you may need to adjust bag and try again.
If you are making initial seal on a piece of bag material
with two open ends, make sure bag is placed on
Sealing Strip, not on rubber gasket (F). If you are
vacuum packaging with a bag, make sure open end is
placed down inside Vacuum Channel and make sure
Accessory Hose (D) is not attached. If you are vacuum
packaging with an accessory, check Accessory Hose in
appliance lid and in accessory to ensure a tight fit.
Check for wrinkles in the bag along the Sealing
Strip. Wrinkles in seal may cause leakage and allow
air to come back into bag. Check for wrinkles in bag
along Sealing Strip (G) before closing lid and vacuum
packaging. If you find wrinkles after sealing bag,
simply cut bag open and vacuum package again.
Copyright © 2004 Tilia, Inc. All rights reserved. This material may not be reproduced or redistributed in any fashion without the express written consent of Tilia, Inc.
FoodSaver and the Freshness Shield logo are trademarks or registered trademarks of Tilia Int’l, Inc. in the United States and other countries. All other trademarks
are property of their respective owners. Tilia, Inc. and Tilia Int’l, Inc. are Jarden companies.This product is protected by one or more of the following Patents:
U.S. RE 34,929; 4,660,355; 4,941,310; 5,655,357; 6,058,998; 6,256,968; Canada 1,315,746; and their equivalent international patents.
First Printing: 6/2004
Item # T180-00210-000 (06/04)
|