Hover Vac
For all customer enquiries or for replacement parts, contact:-
☎
01325 300303
4. Immediately disconnect from the mains electricity sup-
ply if the cable is cut, or the insulation is damaged.
Do not touch the electric cable until the electrical sup-
ply has been disconnected. Do not repair a cut or
damaged cable. Replace it with a new one.
5. Your cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your product.
6. Keep cable away from product, always work away from
the power point using up and down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before winding cable
for storage. Do not repair a damaged cable, replace it
with a new one. Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Our products are double insulated to EN60335.
Under no circumstance should an earth be connect-
ed to any part of the product.
Preparation
1. While using your product always wear substantial
footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones, bones, wire
and debris; they could be thrown by the plastic cutters.
3. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
4. Replace worn or damaged plastic cutters together with
their fixings in sets to preserve balance.
6. Exercise extreme caution when changing direction
on slopes.
7. Using on banks and slopes can be dangerous. Do
not use on banks or steep slopes.
8. Do not walk backwards whilst operating your prod-
uct, you could trip. Walk never run.
9. Never cut grass by pulling the product towards you.
10. Switch off before pushing the product over surfaces
other than grass.
11. Never operate the product with damaged guards or
without guards in place.
12. Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
13. Do not tilt the product when the motor is running,
except when starting and stopping. In this case, do
not tilt more than absolutely necessary and lift only
the part which is away from the operator. Always
ensure that the hand is in the operating position
before returning the appliance to the ground.
14. Never pick up or carry a product when it is operat-
ing or still connected to the mains supply.
15. Remove the plug from the mains :
-
-
-
-
before leaving the product unattended for any period;
before clearing a blockage;
before checking, cleaning or working on the appliance;
if you hit an object. Do not use your product until
you are sure that the entire product is in a safe
operating condition;
-
if the product starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
product is in safe working condition.
2. Check the grassbox frequently for wear or deteriora-
tion.
3. Replace worn or damaged parts for safety.
4. Only use the replacement spare parts and acces-
sories specified for your product.
5. Be careful during adjustment of the product to pre-
vent entrapment of the fingers between moving cut-
ting parts and fixed parts of the machine.
Use
1. Use the product only in daylight or good artificial light.
2. Avoid operating your product in wet grass, where
feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Use across the face of slopes, never up and down.
CABLES
MAINS PLUG REPLACEMENT
IMPORTANT
•
•
If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if a
cut off plug is inserted into a 13 amp socket.
Use only 1.00mm2 size cable up to 40 metres length
maximum.
Maximum rating :
1. No earth required. Our products are double insulated
to EN60335 and under no circumstances should an
earth be connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
1.00mm2 size cable, 10 amps 250 volts AC.
THE HOVER VAC IS SUPPLIED WITH CABLE
WIRED DIRECTLY INTO THE PRODUCT
1. Flymo Mains Cables and Extension Cables are
available from your local Electrolux Outdoor
Products Approved Service Centre.
2. Do not wire an extension cable directly to your product
yourself. Please contact your local Electrolux Outdoor
Products Approved Service Centre for further informa-
tion on the connectors and kits available.
3. Only use extension cables specifically designed for
outdoor use.
The wires in the mains lead are coloured in accor-
dance with the following code:
BLUE
BROWN
-
-
NEUTRAL
LIVE
The wire which is coloured BLUE must be connected to
the Terminal which is marked with the letter 'N' or
coloured BLACK. The wire which is coloured BROWN
must be connected to the Terminal which is marked
with the letter 'L' or coloured RED.
CONNECTORS
IMPORTANT
4. It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
•
Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only pro-
tect the electrical equipment and are not a safe-
guard against electrocution.
•
All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not
be left outside permanently nor should they be sub-
merged or immersed in water. Do not let cable lay
or trail through pools of water or splashed with
water from hose pipes.
If your product is hard wired i.e. non detachable
mains electric cable, a conversion kit and exten-
sion cable is available from all Electrolux Outdoor
Products Approved Service Centres which can be
found in your local yellow pages.
Assembly Instructions
Assembly of lower handle to hood (A)
A
1. Place the ends of the lower handle into the slots
2. Secure lower handle to hood by firmly pushing fix-
ing pin through holes in hood and handle (A1).
3. Repeat on the other side.
•
NOTE
1
Should a problem occur when securing handle with
the fixing pin, carefully lever the pin out of location
and repeat steps 1 to 3 above.
B
lock-off
button
handle
knob
Fitting Upper Handles to Lower Handles (B)
1. Ensure the upper handle is located correctly with
the lock-off button on the switchbox uppermost.
2. Ensure the upper handle and the lower handle are
aligned correctly.
nut
bolt
3. Insert the nut into the handle knob.
washer
4. Fit the bolts, washers and handle knobs.
5. Fit the cable to the handles with the clips provided
making sure the cable is not trapped between the
upper and lower handles.
C
D
Cable clips (C)
1. Fit the cable to the handles with the clips provided.
2. Ensure the the cable is secured under the clip on
the hood.
Starting and Stopping
E
Starting
1. Form loop in mains cable and push the loop
through the slot as illustrated in picture (D).
2. To secure, position loop over the hook and pull the
cable back through the slot as illustrated in picture
(E).
F
3. Connect plug to mains.
4. To prevent a ring being cut in your lawn and to
clear any residual grass in the collection chute, tilt
your lawnmower slightly (F).
• The switchbox is provided with a lock-off but-
ton (G1) to prevent accidental starting.
5. Press and hold the lock-off button (G) on the
switchbox, then squeeze one of the Start/Stop
levers towards the upper handle (H).
6. Continue to squeeze the start/stop lever towards
the upper handle and release the lock-off button.
7. When the product has reached full speed gently
lower it onto the lawn.
• NOTE There are two start/stop levers fitted.
Either one can be used for starting the prod-
uct.
• IMPORTANT Do not use the start/stop levers
intermittently
G
H
1
Stopping
1. To prevent a ring being cut in your lawn, tilt your
product slightly (F).
2. Release the pressure on the Start/Stop lever.
Adjusting the Cutting Height
HIGHEST
This symbol visible
J
K
L
•
•
THERE ARE 2 CUTTING HEIGHTS (J & K)
Height of cut is adjusted by turning over the
cutting head.
LOWEST
This symbol visible
•
Disconnect from the mains electricity supply and
wait until the cutting head has stopped rotating.
Turn your product upside down.
1
•
•
To Remove the Cutting Head and Fan (L)
Hold the fan firmly and twist the cutting head anti-
clockwise as illustrated. Hold the cutting head in
the centre and remove as illustrated. Hold fan in
the centre and remove as illustrated.
Inspect for damage and clean as necessary before
replacing the fan and the cutting head.
3
2
M
•
•
To Refit the Fan and the Cutting Head (M)
Replace the fan as illustrated. Replace the cutting
head, adjusting the height of cut as required. Hold
the fan firmly and twist the cutting head clockwise,
as illustrated.
1
3
IMPORTANT
ENSURE FAN AND CUTTING HEAD ARE COR-
2
RECTLY LOCATED
How to Use
1. Start at the edge of the lawn nearest to the power
point so the cable is laid out on the lawn you have
already cut. (N)
N
2. Cut your grass twice a week during the growing
season, your lawn will suffer if more than a third of
its length is cut at one time.
Do Not Overload Your Product
Using in long thick grass may cause the motor speed
to drop, you will hear a change in the motor sound. If
the motor speed drops you may overload your product
which may cause damage. When using in long thick
grass a first cut with the cutting height set higher will
help reduce the load. See Adjusting the Cutting Height.
Grassbox
P
•
For optimum performance your product is
grassbox is full
designed to be used with the grassbox fitted.
Grassbox full Indicator (P)
•
IMPORTANT
The machine must be switched on for the
grassbox is empty
grassbox full indicator to operate.
1. When the ball reaches the top of the indicator win-
dow, it is time to empty the grassbox. See figure
N.
2. When the ball is NOT visible in the indicator win-
dow, grass is being collected. See figure N.
Emptying the Grassbox (Q)
Q
•
Stop the product and wait until the cutting head
has stopped rotating before emptying the grass-
box.
1. Remove the grassbox lid.
2. Lift the grassbox off the product and empty.
3. Replace grassbox and lid carefully.
•
Failure to fit the grassbox and lid correctly will
cause poor collection of grass clippings.
Cutting System Maintenance
• Always handle the plastic cutters with care -
sharp edges could cause injury. USE GLOVES.
Checking your Cutting System (R)
• The cutting system must be kept in good condition
and inspected before and after use.
R
plastic
cutters
cutting
head
• Disconnect from the mains electricity supply and
wait until the cutting head has stopped rotating.
Turn your product upside down.
1. Visually check cutting head for wear. Replace if damaged.
2. Visually check plastic cutters for wear and replace
when necessary.
fan
3. Plastic cutters should be straight. Replace if bent
or twisted.
hood
Replacing Plastic cutters (S)
• Use only genuine Flymo replacement plastic cutters
specified for this product. These are available from
all Electrolux Outdoor Products Service Centres
and major retail outlets.
S
T
• Plastic cutters must be replaced in pairs to retain balance.
• Two plastic cutters of the same type should be fitted.
• Never fit a metal bar blade to this product.
To Replace Plastic Cutters
• Disconnect from the mains electricity supply and
wait until the cutting head has stopped rotating.
Turn your product upside down.
1. Push plastic cutter towards centre of cutting disc.
Lift plastic cutter away from cutting head. (T)
2. If the plastic cutter is broken during use - lever cut-
ter out of the slot, and dispose of carefully.
3. Fit new plastic cutters into the slots at each side of
the cutting head and pull into place. (V)
V
• IMPORTANT ENSURE PLASTIC CUTTERS ARE
CORRECTLY LOCATED.
Caring
W
• It is very important that you keep your product
clean. Grass clippings left in any of the air
intakes or under the hood could become a
potential fire hazard.
Cleaning (W)
• USE GLOVES
1. Remove grass from under the hood with a piece of
wood or similar.
2. Using a soft brush - remove grass clippings from all
air intakes, the roller, grassbox and grassbox lid.
3. Remove the cutting head, see Figure L, to gain
access to the fan and clean with a soft brush.
4. Wipe over the surface of your product with a dry
cloth.
• IMPORTANT
Never use water for cleaning your product. Do not
clean with chemicals, including petrol, or solvents -
some can destroy critical plastic parts.
At the End of the Season
1. Replace plastic cutters, bolts, nuts or screws, if
necessary.
2. Clean your product thoroughly.
X
3. Ask your local Service Centre to clean the air filter thor-
oughly and carry out any service or repairs required.
4. Make sure that the electric cable is coiled properly.
Carrying your Product : Hold as illustrated in Figure X.
Ensure the cutting head is facing away from you.
Storing your Product Store in a dry place where
your product is protected from damage.
Fault Finding Hints
Fails to Operate
1. Is the Power Turned On?
Poor Collection
1. Is the grassbox fitted correctly?
2. Are you using in straight lines?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
3. Are you cutting more than one third of the grass length?
4. Do you need to raise the cutting height?
5. Follow the procedure described in "Poor Flotation".
Excessive Vibration
Immediately disconnect from the mains electricity sup-
ply and consult your local approved Service Centre.
Poor Flotation
1. Disconnect from the mains electricity supply.
2. Clean the underside of the hood and the fan blades.
3. Raise to a higher height of cut. See Adjusting the
Cutting Height.
1. Disconnect from the mains electricity supply.
2. Replace broken or missing plastic cutters.
3. Check plastic cutters are fitted correctly.
4. If vibration persists?
4. If poor flotation persists?
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Immediately disconnect from the mains elec-
tricity supply and consult your local approved
Service Centre.
Service Recommendations
1. We strongly recommend that your product is serv-
iced at least every twelve months, more often in a
professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most
Electrolux Outdoor Products stockists.
4. Your product is uniquely identified by a silver and
black product rating label
5. If you have a problem with your machine contact
your local Approved Service Centre ensuring you
6. Should it be necessary for work to be carried
out by your Service Centre, it is important to
take your complete machine including cable and
any extension cables used.
A network of specialist dealers can be found in your local
Yellow Pages. To obtain service on your Flymo product
simply telephone or visit your local Service Centre. Should
you require service under the terms of our guarantee the
Service Centre will require proof of purchase.
All of the centres listed stock genuine Flymo Spare
have full details of your product as described on the Parts. NOTE: Our Service Repairers act on their own
product rating label.
behalf and are not empowered to commit or legally bind
Electrolux Outdoor Products in any manner whatsoever.
Environmental Information
Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using,
where practical, components manufactured in the most environmentally responsible manner, according to company
procedures, and with the potential for recycling at the end of the products’ life.
•
•
•
Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
Awareness of the environment must be considered when disposing of ‘end-of-life’ product.
If necessary, contact your local authority for disposal information.
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local council office, your house-
hold waste disposal service or the shop where you purchased the product.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture with-
in the guarantee period, Electrolux Outdoor Products, through its
Authorised Service Repairers will effect the repair or replacement
to the customer free of charge providing:
Failures not covered by guarantee
* Replacing worn or damaged plastic cutters.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
(a)The fault is reported directly to the Authorised Repairer.
(b)Proof of purchase is provided.
(c)The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d)The failure has not occurred through fair wear and tear.
(e)The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised by
Electrolux Outdoor Products.
(f) The machine has not been used for hire.
(g)The machine is owned by the original purchaser.
(h)The machine has not been used commercially.
* Failures as a result of not using the product in accordance
with the instructions and recommendations contained in
this Operator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts
and their life is dependent on regular maintenance and
are, therefore not normally subject to a valid warranty
claim: Plastic cutters, Cutting head, Electric Mains cable.
* Caution!
Electrolux Outdoor Products does not accept liability
under the warranty for defects caused in whole or part,
directly or indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or
approved by Electrolux Outdoor Products, or by the
machine having been modified in any way
*
This guarantee is additional to, and in no way diminishes
the customers statutory rights.
Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator's Manual
and understand how to operate and maintain your machine:
EC Declaration of Conformity
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5
6UP Certify that the Product:-
I, the undersigned M. Bowden of Electrolux
I, the undersigned M. Bowden of Electrolux
Outdoor Products, Aycliffe Industrial Park, NEW- Outdoor Products, Aycliffe Industrial Park,
TON AYCLIFFE, Co. Durham. DL5 6UP Certify NEWTON AYCLIFFE, Co. Durham. DL5
that a sample of the above product has been
tested using directive 81/1051/EEC as a guide.
6UP Certify that a sample of the above
product has been tested using ISO 5349 as
Category........ Electric Lawn Trimmer
Make.............. Electrolux Outdoor Products The maximum A-weighted sound pressure level a guide. The maximum weighted root mean
Conforms to the specifications of Directive recorded at operator position under free field semi square value of vibration recorded at opera-
2000/14/EEC
Type of Cutting Device.... Plastic Cutter
Identification of Series......See Product Rating Label
Conformity Assessment Procedure....ANNEX VI
Notified Body.................... I.T.S., Cleeve Road, Leatherhead,
Surrey. KT22 7SB England
Other Directives:-............. 98/37/EEC, 89/336/EEC, 73/23/EEC
& applicable standards:- EN786, IEC60335-1, IEC60335-2-91,
EN61000-3-2, EN61000-3-3, EN55014-1, EN55014-2
anechoic chamber conditions was :-
tor’s hand position was:-
Type............................................................................
Width of Cut................................................................
Speed of Rotation of Cutting Device..........................
Guaranteed sound power level................................... D
Measured Sound Power Level.................................... E
Level............................................................................ F
A
B
C
Value...........................................................................
Weight.......................................................................... H
G
A
B
C
D
E
F
HV280
28 cm
7,350 RPM
93 dB (A)
92 dB (A)
80.9 dB(A)
Newton Aycliffe, 12/10/04
M. Bowden,
Research & Development Director
2
G
H
2.38 m/s
6.3 kg
Electrolux Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Outdoor
Products manufacture products for a number of well known brands under various registered patents, designs and trademarks in several countries.
© Electrolux Outdoor Products Ltd. Registered Office, Electrolux Works, Oakley Road, Luton LU4 9QQ
Registered number 974979 England
The Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million
Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are
sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
5119692-01
|