Instructions
’
Jeep
®
™
Push’n Scoot
Model Number: 72607
If you experience a problem with this product, or are missing a part,
please call us at 1-800-432-KIDS, rather than return this product to the store.
Please save these instructions for future reference.
Adult assembly is required.
Tools required for assembly: Hammer and Scrap Block of Wood.
Weight Limit: 55 lbs.
1
2
Ages: 1 / years - 5 years.
Assembly
3
CAUTION
Please keep small parts and plastic
bags out of children’s reach. Dispose of
plastic bags properly.
1
Vehicle
Body
Rear Axle
Spacer
Rear Axle
Cap Nut
• Insert the rear axle through the holes in the rear of the
vehicle body. Make sure the spacer fits into the hole in
the vehicle body.
Scrap Block
of Wood
4
Spacer
• Place a cap nut on a scrap block of wood.
• Fit the rear axle into the cap nut and tap with a hammer
until secure.
Rear Axle
Vehicle Body
2
Rear Axle
Spacer
Wheel
Wheel
Scrap Block of Wood
Cap Nut Tool
Spoke Side Down
• Turn the vehicle body on its side with the end of the
rear axle facing up.
• Lift the vehicle body up slightly and fit a cap nut tool on
the cap nut.
• Slide a block of wood under the cap nut tool to support
the rear axle.
• Slide a wheel, spoke side down, onto the rear axle.
• Slide a spacer onto the rear axle.
• Fit the other spacer onto the rear axle and into the hole
in the vehicle body.
3
Assembly
5
7
Bushing
Cap Nut
Cap Nut Tool
Rear Axle
Spoke Side Up
"A" Front Axle
Bushing
Wheel
Washer
• Slide a washer onto the "A" front axle.
• Slide a bushing, narrow side up, onto the "A" front axle.
• Repeat steps 6 and 7 to assemble the "B" front
axle, washer, wheel, bushing and cap nut.
• Slide a wheel, spoke side up, onto the end of the
rear axle.
• Fit a cap nut onto the end of the rear axle.
• Fit a cap nut tool over the cap nut and tap the center
with a hammer until the cap nut is secure.
8
Vehicle
Body
"A" Marking
"A"
Front
Axle
6
Cap Nut
Tool
B
A
Cap Nut
Bushing
Wheel
Spoke Side Up
"A"
Front
Axle
• Turn the vehicle body upright.
• Lift the front end of the vehicle body and locate the
side of the vehicle body marked "A".
IMPORTANT! For proper wheel position, the "A" front
axle assembly must be inserted into the hole in the
vehicle body marked "A".
• Insert the "A" front axle up into the hole underneath
the vehicle body marked "A".
Scrap
Block of
Wood
"A" Front "B" Front
Axle Axle
Washer
• Identify and separate the "A" and "B" front axles.
• Place the "A" front axle onto a scrap block of wood.
• Slide a washer onto the "A" front axle.
• Slide one of the wheels, spoke side up, onto the "A"
front axle.
• Make sure the bushing fits into the hole in the vehicle
body.
• Fit a cap nut onto the end of the "A" front axle.
4
• Fit a cap nut tool over the cap nut and tap the center
with a hammer until the cap nDuotwisnlosaedcfruorme.Www.Somanuals.com. All Manuals Search And Download.
Assembly
9
Cap Nut Tool
Cap Nut
Bushing
Bushing
"A"
Front
Axle
2
1
Vehicle Body
10
9
• Lower the vehicle body.
• Fit a bushing, narrow side down, onto the exposed end
of the "A" front axle and into the hole in the vehicle
body.
Front View
• Fit a cap nut onto the end of the "A" front axle.
• Fit a cap nut tool over the cap nut and tap the center
with a hammer until the cap nut is secure.
9
• Repeat assembly steps 8 and
to assemble the
"B" front axle to the side of the vehicle body marked "B".
• Dispose of the cap nut tools properly.
8
7
10
4
Handle
3
6
5
Hole
Back View
• Make sure the areas where the labels will be applied
are clean and dry.
Hole
• Apply the labels as shown in the illustrations.
• For best adhesion, try to avoid applying a label more
than once.
Rear of
Vehicle
Body
One-time assembly is now complete.
• Position the handle over the rear of the vehicle body so
that it leans away from the vehicle body.
• While keeping the vehicle body stationary, insert and
snap the handle into the two holes in the rear of the
vehicle body.
5
Use
Three (3) Year Limited Warranty
Fisher-Price, Inc., 636 Girard Avenue, East Aurora,
New York 14052, warrants to the original owner that the
Jeep Push 'n Scoot™ is free from all defects in material
and ®workmanship when used under normal conditions for
a period of three (3) years from the date of purchase. This
warranty does not cover color fading of the product or
product parts, or damage from excessive abuse or Acts
of God.
When pushing your child in the Jeep Push 'n Scoot™,
®
use the pull-out footrest.
Footrest
Notches
Should the product fail to perform properly, we will repair
or replace it, free of charge. Purchaser is responsible for
shipping the product to the address indicated above and
for all associated freight and/or insurance cost.
Tab
Tab
Fisher-Price, Inc. will bear the cost of shipping the repaired
or replaced item to you. This warranty is void if the owner
repairs or modifies the product. This warranty excludes any
liability other than the above mentioned, including but not
limited to any incidental or consequential damages.
Seat
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLU-
SION MAY NOT APPLY TO YOU.
• Pull the footrest out from under the seat.
• Hook the notches in the front of the footrest onto the
tabs on the inside front of the Jeep Push 'n Scoot™.
®
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE.
Maintenance
• Periodically check the Jeep Push 'n Scoot™ to be sure
all fasteners are secure and re-fasten as needed.
• To clean or remove static electricity, use a mild soap
and water solution and a clean cloth. Rinse clean with
water to remove soap residue.
®
Questions?
We'd like to hear from you!
Call Fisher-Price® Consumer Affairs, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday through
Friday. Hearing-impaired consumers using TTY/TDD
equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price® Consumer Affairs, 636 Girard Avenue,
East Aurora, New York 14052.
JEEP and Jeep grille design are registered trademarks of Chrysler Corporation U.S.A. Used under license.
© CHRYSLER CORPORATION 1997.
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to: Mattel/Fisher-Price, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone 01734 770488.
In Australia, call the Fisher-Price Australian Consumer Advisory Service toll-free at 1-800-800-812, or write to: Fisher-Price, Mattel Pty. Limited, 461 Plummer Street,
Port Melbourne, Victoria 3207.
©1997 Fisher-Price, Inc., East Aurora, New York 14052
Printed in U.S.A.
72607 1 72607-0920
|