AS1060- AS1069 Series
Upright vacuum cleaner; household type.
Owner’s Guide
Thank you for purchasing your new Eureka vacuum
Important instructions
For easy assembly, please take a few
moments to read this owner’s guide.
To view an assembly video, go to Eureka.com/
videos or scan QR code. If you have questions
about your new vacuum, please contact our
customer service helpline at 1-800-282-2886.
We're here to help!
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturday - Sunday
Guía del Propietario
¡Gracias por la compra de su nueva aspiradora
Eureka!Pour visualiser la vidéo d’assemblage, rendez-vous à
Para ver un video del ensamblaje, diríjase a Eureka.com/videos
o escanee el código QR. Si tiene alguna pregunta sobre su
nueva aspiradora, póngase en contacto con la línea de ayuda
del servicio al cliente al
1-800-282-2886. ¡Estamos para ayudarle!!
8 a.m. a 7:30 p.m. (CST), de lunes a viernes
10 a.m. a 6:30 p.m. (CST), sábado y domingo
Le Guide du Propriétaire
Merci d’avoir acheté votre nouvel aspirateur
Eureka!Pour visualiser la vidéo d’assemblage, rendez-vous à
Pour visionner une vidéo d'assemblage, allez au Eureka.com/
videos ou balayez le code QR. Si vous avez des questions sur
votre nouvel aspirateur, veuillez téléphoner à notre ligne
d'assistance-client au
1-800-282-2886. Nous sommes là pour vous aider!
8 h à 19 h 30 (CST), lundi au vendredi
10 h à 18 h 30 (CST), samedi et dimanche
© 2014 Electrolux Home Care Products, Inc.Printed in China PN 88453
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical
cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer's recommended attachments.
!
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to a service center before using.
• Do not pull or carry by cord. Do not use cord as a handle. Do not close a door on cord or pull cord
around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from
heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Hold plug when rewinding into cord reel. Do not allow plug to whip when rewinding.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose clothing,
fingers, and all parts of body away from openings and moving parts.
• Do not place vacuum cleaner on furniture or stairs as the brush roll may cause damage. Use extra
care when cleaning stairs. Place vacuum cleaner on floor with the handle in storage
position while using attachments.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust cup, filter and screen, and HEPA exhaust filter in place.
• Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley
when servicing the drive belt.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where
they may be present.
• Store your vacuum cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
• Unplug before connecting turbo nozzle.
SAVE THESE INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
Motor
Do Not Oil the motor or the brush roll at any time. The bearings are permanently lubricated
and sealed.
Eureka Customer Service HELPLINE 1-800-282-2886
1
How to identify parts of vacuum cleaner
SPECIAL FEATURES
Available on some models
Handle
Cord clip
Turbo nozzle
(on some models)
Carry handle
Turbo
nozzle
Hose
Dust cup release
WAND
2
Air pa
selector kn
Filter and screen
(located inside dust cup)
Wand
Turbo cover
Wand 2
Dust cup
Crevice tool
Dusting brush
Cord rewind switch
Exhaust/HEPA
filter compartment
(located behind dust cup)
Power co
Cord re
Lower hose retainer
Base hose
Power switch
Brushroll on/off pedal
Brush roll cover
Handle release
Height
adjustment knob
Maintenance schedule
Maintenance Schedule is also located on back side of dust cup.
I
!
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. Moving parts! Power switch is marked
for On/Off.
DUST CUP – Empty after each use
Press lever to release bottom lid.
Debris will empty.
Close bottom lid
until it clicks.
FILTER DCF21 – Replace or clean regularly to maintain suction
Filter
DCF21
Empty cup. Pull back
latch to lift off lid.
For quick clean, Grasp filter and twist to remove
tap filter. from lid. Shake dust from filter.
Screen
Remove screen. Rinse
screen and dust cup.
Dry thoroughly.
Align tab with slot to Reinstall filter. Align lid
reinstall screen.
at front; press down until
lid snaps into place.
Exhaust filter
EF6
( HEPA filter
on some models)
EXHAUST FILTER EF6 – Check filter regularly. Replace every
6-12 months or when performance loss is noticeably declining
W belt
Remove dust cup. Press down tab and Lift out filter and replace. Reinstall
remove filter cover.
cover and snap into place.
BRUSH ROLL – Clean monthly
Brush roll
W BELT – Replace worn, cut or out of shape belt
2
Eureka Customer Service HELPLINE 1-800-282-2886
How to use accessories
C A U T I O N
When using tools, always place handle
in upright position to raise vacuum to
highest carpet setting. Brush roll will
continue to turn when vacuum is turned
on and handle is in upright position. Do
not tilt vacuum forward while using tools.
To avoid damage, do not set vacuum on
carpet, carpeted stairs, furniture or
fringed rugs when using tools.
Fig.1
Fig. 2
Before using accessories
•
Turn air path selector knob to ‘tools’ (Fig. 1).
• Pull out cord to desired length.
Do not pull past red line (Fig. 2).
• Push cord into cord clip (Fig. 3).
• To store, press switch to retract cord (Fig. 4).
2-Position wand
WAND
1
(wand 2 on some models or available for purchase)
• Loosen wand and hose from vacuum.
• Push tool onto end of wand (Fig. 5).
Fig.3
Fig.4
• Short wand: Push hose release button to
remove wand 1. Attach tool to end of hose.
WAND
2
• Longer wand: Slide off wand 2 and turn over,
then push opposite end onto wand 1.
Dusting brush
Wand 1
Use for furniture, drapes and vents.
Crevice tool
Use for baseboards, corners
Wand 2 (on some models)
Fig.5
and tight spaces.
Turbo nozzle
(on some models or available for purchase)
Use for furniture and stairs.
Stairs – make sure vacuum is below
you, pushed against the bottom step.
• Attach turbo nozzle to end of hose.
NOTE: Hose length can be increased by
releasing the hose from the hose retainer
on back of unit. Reposition hose inside
hose retainer after using accessories.
Eureka Customer Service HELPLINE 1-800-282-2886
3
How to maintain your vacuum cleaner
!
Make sure vacuum cleaner is turned off and power cord is unplugged.
Maintain brush roll
Motor pulley can become hot with normal use.
Remove hair and threads from brush roll periodically. Do not remove end caps.
Check W belt. Replace if worn, cut or out of shape.
Avoid touching the motor shaft when checking brush roll or belt.
!
How to replace brush roll or belt
• Step on handle release to lower handle flat
onto floor (Fig.1).
• Remove 4 screws from brush roll cover.
(Fig. 2).
Fig.1
Fig. 2
Fig. 4
Fig. 6
• Lift off brush roll cover. (Fig. 3).
• Remove brush roll and belt. Thread new
belt around motor shaft and brush roll
(Fig. 4).
• Insert left end of brush roll first. Make sure
end cap fits into base. Pull right side of
brush roll to stretch belt and insert right
end cap into base (Fig. 5). Make sure it
slides into position.
Fig. 3
• Rotate brush roll 2 turns to center belt.
• Replace brush roll cover (Fig. 3).
• Replace 4 screws (Fig. 6).
Fig. 5
How to clear a blockage
Make sure vacuum is turned off and power cord is unplugged.
!
Hose blockage
• Remove hose from hose retainer. Flex the
hose to loosen any blockage (Fig.1).
•
Remove dust cup. Set air path knob to ‘floors.’
Use finger to check for debris (Fig 2).
Fig. 1
Fig. 2
• Base hose – Pull down to loosen end of
base hose. Use finger to clear blockage.
Snap hose end back up into position (Fig 3).
• Hose connector – Pull out on left side tab
to remove connector. Remove debris. Align
tab at right and snap connector back into
place (Fig. 4).
Fig. 3
Fig. 4
4
Eureka Customer Service HELPLINE 1-800-282-2886
How to maintain turbo nozzle
(on some models)
1) Turn nozzle onto back
side. Remove 1 screw.
2) Rotate lower part of
cover down over brush
and lift off cover.
3) Clear blockage from
brush roll area. Use
scissors to clip
4) Place cover back
into position.
Tighten screw.
threads or hair.
The Eureka limited warranty
USA: 1-800-282-2886
Electrolux Home Care
North America Service Division
P.O. Box 3900
Mexico: (55) 5343-4384 Canada: 1-800-282-2886
Eureka warrants this vacuum cleaner to be free from defects in
material and workmanship for a term of three years for normal
household use. Warranty is granted only to the original
purchaser and members of immediate household.
Electrolux Home Care
Electrolux Home Care
North America Service Division
5855 Terry Fox Way
Mississauga, Ontario L5V 3E4
Peoria, IL 61612
This warranty is good for three years from the date of purchase
only when the vacuum cleaner is used in the accordance with
Eureka operating instructions. Note: refurbished or
Obtaining warranty service
outside your community
You must pay the shipping charges to the Eureka Authorized
Warranty Station.
remanufactured products have a one year limited warranty.
This warranty does not cover
Return shipping charges will be paid by the Warranty Station.
When returning parts for repair, please include the model, type
and serial number located on the rating plate on the lower
backside of the vacuum.
• Parts of the vacuum that require replacement under
normal use such as disposable dust bags, filters,
drive belts, light bulbs, brush roll, bristles, impellers
and cleaning.
Further limitations and exclusions
• Damages or malfunctions caused by negligence,
abuse, and use not in accordance with the
Owner’s Guide.
Any warranty that may be implied in connection with your
purchase or use of the vacuum, including any warranty of
Merchantability or any warranty for Fitness For A Particular
Purpose is limited to the duration of this warranty. Some states
do not allow limitations on how long an implied warranty lasts,
so the above limitations may not apply to you.
• Defects or damages caused by unauthorized
service or the use of other than Genuine Eureka,
ARM & HAMMERTM and FiltreteTM by 3M parts.
Your relief for the breach of this warranty is limited to the relief
expressly provided above. In no event shall the manufacturer
be liable for any consequential or incidental damages you may
incur in connection with your purchase or use of the vacuum.
What Eureka will do
Eureka will, at its option, repair or replace a defective vacuum
or vacuum part that is covered by this warranty. As a matter of
warranty policy, Eureka will not refund the consumer’s
purchase price.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
Obtaining warranty service
To obtain warranty service you must return the vacuum
or vacuum part along with “proof of purchase” to any Eureka
Authorized Warranty Station. For Eureka Authorized Warranty
Station or Service Information, visit www.eureka.com,
write or telephone toll free:
This warranty gives you specific legal rights.You may
also have other rights, which may vary by state.
The ARM & HAMMER name is a trademark of Church and Dwight Co., Inc.
3M and Filtrete are trademarks of 3M Company, used by Electrolux Home Care
Products, Inc. under license.
Eureka Customer Service HELPLINE 1-800-282-2886
5
Problem solving
!
Make sure vacuum is turned off and power cord is unplugged.
N O T I C E : Thermal cut-off
This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off, proceed as follows:
1) Push the power switch to off and unplug the vacuum.
2) Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them
and wait at least 30 minutes before attempting to use the vacuum.
3) After the 30 minute period, plug the vacuum back in and turn on the switch. If the vacuum still does not work, call the Eureka customer service helpline.
Problem
Cause
Solution
Power plug
• Push plug securely into outlet, try another outlet or
check circuit breaker.
Motor will not start.
Power switch
• Step on power switch to turn vacuum on.
Thermal cut-off
Dust cup and filter
• See detailed "thermal cut-off" instructions above.
• Empty dust cup, clean and/or change filter.
• Clean or replace filters regularly to maintain suction. Page 2
Vacuum does not clean
carpet or bare floor.
• If picking up fine dust, the dust cup may not look full, but a fine substance
tends to reduce suction when it blocks air flow through the filter and screen.
Refer to page 2 for filter maintenance. Make sure filter, screen and dust cup
are installed properly.
Air path selector
• Turn selector knob to ‘floors.’
Belt
• Replace a worn, cut or out of shape belt. Page 4
Hose
• Remove clogs from the hose that restrict the airflow. Make sure hose
is replaced into hose retainer. Page 4
• For bare floor cleaning, turn height adjustment knob
to bare floor position. Step on brushroll on/off pedal to
turn off the brushroll.
Bare floor setting
For carpet cleaning, step on the brushroll on/off pedal to ensure the brushroll
is on. Adjust height adjustment knob to appropriate carpet height setting.
•
Carpet height setting
Dust cup and filter
• Empty dust cup, clean and/or change filter.
No suction at the
end of hose.
• Clean or replace filters regularly to maintain suction. Page 2
• If picking up fine dust, the dust cup may not look full, but a fine substance
tends to reduce suction when it blocks air flow through the filter and screen.
Refer to page 2 for filter maintenance. Make sure filter, screen and dust cup
are installed properly.
Air path selector
Hose
• Turn selector knob to ‘tools.’
• Remove clogs from the hose that restrict the airflow. Make sure hose
is replaced into hose retainer. Page 4
Turbo nozzle will not turn
(on some models).
Rotating brush
• Check turbo nozzle for debris. Page 5
• If no suction at end of hose, turn selector knob to ‘tools.’
Vacuum is hard
to push.
Vacuum height setting
• Adjust knob to a higher position.
Belt
Belt
• Replace a worn, cut or out of shape belt. Page 4
Burning smell; brush roll
will not turn.
• Check brush roll for debris. Page 4
• Replace broken or out of shape belt. Page 4
Cord will not rewind fully.
Cord tangles
• Pull out entire cord removing any kinks, and push button to rewind
completely.
6
Eureka Customer Service HELPLINE 1-800-282-2886
|