Installation instructions
and user guide
Food waste disposer
GD50S1
NZ
1
Contents
Safety and warnings
Installation instructions
Operating instructions
Cleaning and maintenance
Troubleshooting
2
3
8
9
10
11
12
Manufacturer’s warranty
Customer care
Important!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please go to our website listed on the back cover
or contact your local Fisher & Paykel dealer.
2
Safety and warnings
Use this appliance only for its intended purpose as described in this User Guide.
Important safety precautions !
When using this appliance, always use basic safety precautions, including the following:
Danger!
This appliance is not intended for the use by children or infirmed persons without supervision.
To reduce the risk of injury, close supervision is required when a waste disposer is used
near children.
Do not put fingers or hands into the waste disposer.
Unplug the unit before attempting to clear a jam or remove an object from the disposer.
As the waste disposer is magnetic, use only non-magnetic tools such as a wooden spoon or
long handled plastic tongs when attempting to loosen a jam or remove objects from the
waste disposer.
To reduce the risk of injury by materials that may be expelled by a waste disposer, do not put
non-food items, or any of the following into the food waste disposer:
a) Shells, such as mussel or oyster shells.
b) Caustic drain cleaners or similar products.
c) Glass, china or plastic.
d) Large whole bones.
e) Metal, such as bottle caps, tin cans, utensils or aluminium foil.
f) Hot grease or other hot liquids.
g) Whole corn husks or similar fibrous material.
When not operating the waste disposer, leave the drain stopper in place to reduce the risk of
objects falling into the disposer.
Your new appliance must be properly installed in accordance with the installation instructions
before it is used.
Never unplug the waste disposer by pulling on the power cord.
Always grip the plug firmly and pull straight from the outlet.
Repair or replace immediately all electric service cords that have become frayed or
otherwise damaged.
Power cords must be replaced by a qualified electrician or authorised service engineer.
Do not use a cord that shows cracks or abrasion along it’s length or at either the plug
or appliance end.
WARNING!
Electrical Shock Hazard
To reduce the risk of electric shock or injury to persons, read the IMPORTANT SAFETY
PRECAUTIONS before operating this appliance.
SAVE THESE INSTRUCTIONS
3
Installation instructions
Before you begin
Please read these installation instructions completely and carefully.
The following installation instructions are intended as a general guide.
Please ensure that the waste disposal unit is installed according to local building codes for
your area.
Installation is recommended to be done by a qualified plumber or installer.
Product failure due to improper installation is not covered under the Warranty.
Preparation
Removing an existing waste disposer, if installed
1
2
3
Disconnect electrical power supply to existing disposer.
Remove old disposer or sink flange assembly.
Inspect drain line. If it is heavily coated with hardened grease and accumulations, clear out the
build-up using a plumber’s rod or auger.
4
Remove old sealing materials and gaskets from sink opening, both top and bottom.
What you will need
Phillips screwdriver
Flat blade screwdriver
Steel Punch or wooden dowel
Petroleum jelly or liquid soap
Plumber’s Putty
Important!
Top and bottom of sink and sink flange surfaces must be free of any materials to prevent leaks.
4
Installation instructions
Unpacking your waste disposer
1
1
2
Remove the waste disposer from the packaging.
Identify and check that all components are
included in the carton before beginning the
installation (fig. 1).
2
3
4
3
Take care not to misplace any of the
components.
5
6
7
Components
8
1. Stopper
2. Sink flange
3. Rubber gasket
4. Flange ring
9
5. Protector ring
6. Mount ring
7. Screw clamp
8. Hopper with splash guard
9. Dishwasher discharge inlet
10. Drain housing
11. Reset button
10
11
12. Lower shell
13. End Bell (Electrical Connections)
14. Power cord
12
13
15. Outlet gasket
16. Discharge waste elbow
17. Waste elbow flange nut
14
Fig 1. Three Bolt Mount System
15
16
17
Fig 1.2. Elbow
5
Installation instructions
Installation
1
2
Loosen the clamp screw to allow the mounting system to be
removed (fig.2).
Turn the mounting assembly over and remove the flange ring
from the track on the sink flange. Undo the three screws holding
it together. This will allow the sink flange, mount ring, and
protector ring to separate (fig 3).
Fig. 2 Removing the mounting
system from the waste disposer
Use the flat blade screwdriver as a lever if required.
3
4
Apply a small amount of plumbers putty to the lip of the flange
and position the sink flange into the sink drain hole ensuring
that the rubber gasket on the underside of the sink flange is
firmly in place (fig.4).
Approaching from under the sink, slide the protector ring
and mount ring onto the underside of the sink flange. Fit the
flange ring into the track on the sink flange, then tighten the 3
mounting screws evenly and securely (fig.5).
Fig. 3 Disassembling the
mounting system
Note:
Ensure that the mounting assembly connection is fixed securely
and tightly.
Fig. 4 Fitting the flange
into the sink drain hole
No dishwasher connection required
If a dishwasher is not being connected, please proceed to step 7.
Connecting to a dishwasher
If you are connecting to a dishwasher, please continue with
steps 5 & 6.
5
Using a blunt instrument (steel punch or wooden dowel), knock
out the entire plug at the end of the dishwasher drain inlet (as
shown in fig.6). Do not use a screwdriver or sharp instrument.
When the knockout plug falls into disposer, you may remove
it or simply grind it up when the disposer is used. This will not
damage the disposer in any way, but may take some time to
grind, over the course of several uses.
Fig. 5 Fixing the mounting system
to the underside of the sink
6
Connect the dishwasher drain hose to the dishwasher inlet pipe
on the waste disposer (fig. 6). Use a clamp to ensure a tight
seal. A stepped rubber adaptor (not supplied with the product)
may be required if the diameter of the drain hose is larger than
the diameter of the waste disposer’s inlet connection.
Fig. 6 Connecting to a
dishwasher (if required)
6
Installation instructions
7
8
Connect the discharge elbow to the lower outlet on the waste
disposer (fig. 7).
Prior to connecting the waste disposer to the mounting
assembly, press firmly down on the rubber splash guard to
check that is firmly fitted onto the neck of the hopper.
9
Lubricate the top lip and angled surface of the rubber splash
guard with liquid soap or petroleum jelly (fig. 8 ).
Fig. 7 Connecting the discharge
elbow
Important!
Please do not remove clamp and splash guard from hopper. Both parts
are factory installed and installation ready.
10 Align the discharge elbow up with the waste pipe (refer to
fig.11) so that the waste disposer is correctly positioned, prior to
engaging with the mounting assembly.
Fig. 8 Lubricate the rubber
splash guard
11 Guide the waste disposer up to the sink flange (fig. 9). Engage
the groove of the splash guard around the ridge at the bottom
of the sink flange. A slight rocking motion may be required to
help ensure a proper fit.
12 While still supporting the body of the waste disposer, tighten
the screw clamp around the rubber splash guard (fig.10). The
waste disposer will now hang by itself.
Fig. 9 Engage the waste disposer
13 Connect the discharge elbow up with the waste pipe (fig.11)
and tighten the slip nut on the drain pipe.
Note:
If you need to rotate the waste disposer to connect with the
waste pipe, it is important to make sure the sink flange does
not turn. Movement of the sink flange will break the seal. If this
occurs, disengage the waste disposer from the discharge elbow
and mounting assembly Return to step 10 to realign the waste
disposer before repeating steps 11-13.
Fig. 10 Tightening the clamp
Important!
Ensure that the reset button is readily accessible after installation of the
waste disposer.
Fig. 11 Connecting the drain
outlet
7
Installation instructions
Controlling the waste disposer
All electrical connections MUST be done by a registered electrician. The waste disposer must
be connected to the power supply by an earthed 3-pin outlet socket, mounted adjacent to the
waste disposer under the sink.
Wall mounted switch
The waste disposer can be controlled by means of a wall mounted power switch, positioned
500mm minimum away from the sink.
Bench mounted air switch
An alternative option to a wall mounted control switch is a bench mounted air switch positioned
within easy reach next to the sink.
We recommend using an Easy Fit by Fisher & Paykel Air Switch, which is available as an optional
accessory from your Fisher & Paykel retailer or can be purchased through Fisher & Paykel Spare
Parts (Part no. 2001105).
8
Operating instructions
Operating instructions
1
Remove the sink stopper and turn on a medium flow of cold water.
Note:
Do not use hot water. Only cold water should be run through the waste disposer.
2
3
Press the wall mounted control switch, or an air switch if fitted, to activate the waste disposer.
Feed food items through the sink opening of the waste disposer gradually.
Note:
Overloading the waste disposer with too much food waste at once may cause the blades to jam
and the disposer to shut down. The overload button may be required to be reset. Refer to the
Overload Reset button section on page 9.
Caution!
Do not put hands or fingers into the waste disposer.
4
Before turning the waste disposer off, let the water and the disposer run for approximately half a
minute after shredding stops. This assures that all the food waste is thoroughly flushed through
the trap and drain.
Helpful Hints
If a dishwasher drain hose has been connected to the waste disposer, be sure that the waste
disposer’s chamber is empty before using the dishwasher to ensure the dishwasher is able to
drain properly.
It is recommended to leave the stopper in the drain when the disposer is not in use to prevent
utensils and foreign objects from falling into the waste disposer.
The waste disposer is designed to give you years of trouble-free service. The grinding mechanism
is built to handle all normal food wastes, but WILL NOT grind and dispose of items such as tin
cans, bottles, bottle caps, glass, china, leather, large bones, mussel or oyster shells. These are
waste materials that should be collected with your household rubbish.
We recommend cutting or breaking up items which require considerable grinding time, such
as melon rinds, grapefruit skins, small bones and corn cob husks or dispose of these items with
your household waste collection.
9
Cleaning and maintenance
Your waste disposer is self-cleaning and scours itself with each use. Under normal usage, your
waste disposer will not require any special care.
Note:
Always run cold water into the chamber before, during and after using the waste disposer.
Do not use hot water.
Removing an odour
Grinding up a tray of ice cubes will help to clean the shredding plate.
Running orange or lemon rinds through the waste disposer will help to freshen up the
grinding chamber.
Note:
Do not pour bleach or drain cleaners, into the waste disposer
Never put corrosive substances or chemicals into the waste disposer.
Unblocking a jam
Before investigating a blockage, you MUST disconnect the power supply.
1
2
The waste disposer is magnetic. ALWAYS use non-magnetic tools, such as a wooden spoon or
long handled plastic tongs when attempting to loosen a jam or remove an object from the
waste disposer.
After clearing the blockage or jam, turn the power back on, turn on a medium flow of cold
water and run the waste disposer for half a minute to ensure that all the food waste is
thoroughly flushed through the trap and drain.
3
Note:
If the motor does not start when activated, refer to the Overload Reset Button section below or
the Troubleshooting guide on page 9.
Overload Reset button
The waste disposer is fitted with an overload control which prevents the motor from operating
should overloading occur.
Overloading occurs when the motor is unable to turn, usually caused by a foreign object
falling in to the chamber or too much food waste being fed through into the chamber at once,
jamming the shredding plate. When overloaded the motor will stop automatically. To restart the
motor the overload reset button must be pressed.
The reset overload button is a small red button located opposite the power cord outlet, near the
bottom of the waste disposer. Before resetting the overload button, you MUST disconnect the
power supply.
Important!
The motor is permanently lubricated for life. Do not attempt to lubricate your waste disposer.
10
Troubleshooting
Troubleshooting tips
Problem
Possible causes
What to do
Waste disposer No electricity at the power
Check that the plug is correctly connected and power
is turned on
is not starting
outlet
Check another appliance at the same outlet
Check house fuse
Foreign object may be
lodged between the
Turn power supply and water tap off. Rotate the
turntable, using a plastic, wooden or non-magnetic
turntable and grinding ring implement to dislodge the foreign object
Grinding chamber may be Turn the power and water tap off and, using a plastic,
overloaded with food waste wooden or non-magnetic implement, remove the
or foreign matter
food waste or foreign matter. Refer to the operating
instructions section
Safety overload button
may have tripped
The reset overload button is a red button located
externally, opposite the power cord outlet, near the
bottom of the waste disposer
Abnormal noise A spoon, bottle cap or
when operating other foreign object may
have fallen into the waste
Turn power supply and water tap off. Wait until
grinding blades and turntable has stopped turning.
Use a plastic, wooden or non-magnetic implement to
remove the foreign object
disposer
Waste disposer Foreign object may be
Turn power supply and water tap off. Rotate the
turntable, using a plastic, wooden or non-magnetic
is jammed
lodged between the
turntable and grinding ring implement to dislodge the foreign object
Unit is leaking
at the top
connections
Improper seating of the
sink flange
Check that the sink flange is centred and sealed
tightly into the sink drain by the mounting assembly
from underneath. Refer to step 2 of the installation
instructions
Improperly installed rubber Check that the rubber gasket is sitting flat under the
gasket
lip of the sink flange. Refer to step 2 of the installation
instructions
Mount ring not tightened
properly
Discharge outlet elbow may not be tightened.
Check the discharge elbow is tight. Refer to step 13 of
the installation instructions
Unit is leaking
Discharge outlet elbow may Check the discharge elbow is tight. Refer to step 13 of
at the discharge not be tightened
outlet
the installation instructions
Water is slow to Rubber splash guard
When the rubber splash guard is new, air can become
trapped within the chamber preventing water from
draining quickly. Pushing food through the rubber
splash guard will release the air and the water will
drain. Over time, the splash guard fingers will soften
and flex, holding back less air and aiding drainage
drain from the
sink
fingers trapping air inside
the chamber
11
Manufacturer’s warranty
Fisher & Paykel undertakes to
Repair or, at its option, replace without cost to the owner either for material or labour any part of
the Product, the serial number of which appears on the Product, which is found to be defective
within TWO YEARS from the date of purchase.
This warranty DOES NOT Cover
A
B
Service calls which are not related to any defect in the Product. The cost of a service call will be
charged if the problem is not found to be a Product related fault. For example:
1. Correct the installation of the product.
2. Instruct you how to use the product.
3. Replace house fuses or correct house wiring.
4. Correcting fault(s) caused by the user.
5. Correcting damage caused by pests, eg. rats, cockroaches etc.
Defects caused by factors other than:
1. Normal domestic use or
2. Use in accordance with the Product’s User Guide.
C
D
Defects to the Product caused by accident, neglect, misuse or ‘Act of God’.
The cost of repairs carried out by non-authorised repairers or the cost of correcting such
unauthorised repairs.
E
F
Normal recommended maintenance as set out in the Product’s User Guide.
Repairs when the appliance has been dismantled, repaired or serviced by other than a
Fisher & Paykel AUTHORISED CUSTOMER SERVICE CENTRE or the selling dealer.
Pick up and delivery.
Transportation or travelling costs involved in the repair when the product is installed outside the
Fisher & Paykel AUTHORISED CUSTOMER SERVICE CENTRE’S normal service area.
G
H
Service under this manufacturer’s warranty must be provided by an Authorised Service Agent
(refer to the Customer care section for contact details). Such service shall be provided during
normal business hours. This warranty certificate should be shown when making any claim.
Note:
This Warranty is an extra benefit and does not affect your legal rights and applies only to product
purchased in New Zealand and Australia.
Please keep this User Guide in a safe place.
Do not return to Fisher & Paykel.
12
Customer care
Check the things you can do yourself.
Refer to your User Guide and check:
1
2
your appliance is correctly installed
you are familiar with its normal operation
If after checking these points you still need assistance, please refer to your nearest
Authorised Service Centre, or contact us through our local website listed on the back cover.
In New Zealand if you need assistance...*
Call your Fisher & Paykel retailer who is trained to provide information on your appliance, or if we
can be of any further help, please contact our Customer Care Centre,
Toll Free: 0800 FP CARE or 0800 37 22 73
Email: [email protected]
Fax: (09) 273 0656
Postal address: P.O. Box 58732, Greenmount, Auckland
If you need service...*
Fisher & Paykel has a network of independent Fisher & Paykel Authorised Service Centres whose
fully trained technicians can carry out any service necessary on your appliance. Your dealer or
our Customer Care Centre can recommend an Authorised Service Centre in your area.
In Australia if you need assistance...*
Call the Fisher & Paykel Customer Care Centre and talk to one of our Customer Care Consultants.
Toll Free: 13 00 650 590
Fax: (07) 3826 9298
Email: [email protected]
Postal Address: PO Box 798, Cleveland QLD 4163
If you need service...*
Fisher & Paykel Australia Pty Ltd has a network of independent Fisher & Paykel Authorised
Service Centres whose fully trained technicians can carry out any service necessary on your
appliance. Our Customer Care Centre can recommend an Authorised Service Centre in your area.
*If you call or write, please provide: name, address, model number, serial number, date of
purchase and a description of the problem. This information is needed in order to better respond
to your request for assistance.
Product Details
Fisher & Paykel Appliances Ltd
Model/Serial No.
Date of Purchase
Dealer
Purchaser
Suburb
Town
Country
13
Copyright © Fisher & Paykel 2008. All rights reserved.
The product specifications in this booklet apply
to the specific products and models described at
the date of issue. Under our policy of continuous
product improvement, these specifications may
change at any time. You should therefore check
with your Dealer to ensure this booklet correctly
describes the product currently available.
NZ
Food waste disposer installation
and user guide
Published: 09/2008
Part No. 791633
|