G136.qxd:G29 09/05.qxd 28/7/11 09:31 Page 1
EARLEX HG1200
Thank you for purchasing the Earlex heat gun.
This is a highly versatile tool that can be used in a
variety of applications.
BEFORE USE - PLEASE READ THE SAFETY &
OPERATING INSTRUCTIONS
Please retain for future reference
G136.qxd:G29 09/05.qxd 28/7/11 09:31 Page 3
OPERATION
Removing paint - general
Before starting work it is advisable to test the
work surface for the ideal temperature to
use. The table below gives an indication of
the likely heat settings required but always
start with the low heat setting. All
Do not heat the paint for too long as this
will burn the paint, making it difficult to
remove.
1.Choose the required nozzle and fit
onto the heat outlet.
applications, with the exception of removing
paint from window frames, can be performed
without using a nozzle, however for best
results nozzles are recommended.
2.Hold the gun with nozzle approximately
50mm (2”) from surface of paintwork.
3.Starting with the low heat setting, move
the gun slowly backwards and forwards
until the paint blisters and bubbles.
4.Immediately remove the paint with a
scraper or shavehook.
Suggested Ratings
Low
Welding plastic
5.Aim to heat the paint just ahead of the
scraper so that you can develop a
continuous action.
High
Paint stripping
Bending plastic
Heat shrinking
plastic
Defrosting pipes
Removing vinyl
floor tiles
Soldering
Lighting BBQs
Removing paint from window frames
WARNING – Glass can break easily when
heated.
1.Use the glass protection nozzle.
2.Ensure the nozzle is facing the correct
way to deflect heat away from the
glass before you switch on the heat
gun.
Nozzles
3.Rotate the gun/nozzle 90º as you move
to horizontal or vertical bead (take care
it could be hot!).
The gun is supplied with two different
shaped nozzles, which can be used as
follows:
4.Paint can be removed by using a
shavehook and/or a soft wire brush.
Concentrator Nozzle - G84
Maintenance
G
Directs a
Always allow the machine to cool down
(before storing) and disconnect from the
power supply. The heat gun should be
cleaned before being stored away by wiping
over with a clean damp cloth. DO NOT USE
CHEMICALS. Ensure that the ventilation
slots are not blocked.
G84
concentrated heat
flow to the work
surface.
G
Ideal for removing
paint in awkward
corners, crevices,
mouldings,
beading or
architraves.
Trouble Shooting
Concentrator nozzle
If a problem occurs always switch off the
unit immediately and disconnect from
power supply.
Glass Protection Nozzle - G89
My unit fails to work?
G
Deflects the heat
G89
If you are using an extension cable it must
be fully unwound and rated at 15 amps
capacity.
away from glass
or other fragile
areas.
Refer to ʻThermal cut outʼ on page 2.
G
Ideal for window-
Glass
sills, ledges,
protection nozzle
frames and
base boards.
3
G136.qxd:G29 09/05.qxd 28/7/11 09:31 Page 4
WARRANTY
This product is guaranteed for a period of 24 months against faulty materials and workmanship. While
every possible care is taken by Earlex to ensure that our products leave the factory in good working order,
Earlex cannot under any circumstances accept liability for problems or damage caused by their
subsequent use. It is the responsibility of the user to ensure that surfaces to be treated, cleaned or
stripped are suitable for this product. This warranty does not affect your statutory rights. This warranty
excludes the use for hire purposes. In the event of a fault occurring please contact our helpline before
returning the unit to our Service Department at the address below together with a copy of your purchase
receipt. All repairs will be dealt with promptly.
IF YOU REQUIRE FURTHER ASSISTANCE PLEASE CONTACT OUR HELPLINE ON:
Earlex reserves the right to modify or improve this product without prior notice.
Colors may vary from those shown.
For information on other products in the Earlex range, please contact us at the address below or visit our
Earlex Inc.
8261 Highway 73, Suite F,
Stanley, N.C. 28164, USA
Earlex Inc, Toll Free 888-783-2612
G136 07/11
©Earlex Inc. 2011
|